Boat Trailer Specifications

I need to replace the boat triler tires but cannot find the size I need. Is there another tire number that will meet the specifications?

Go to any automotive tire store, they will set you up.

2008-03-16 17:34:30 by jtmmiller1@sbcglobal.net

www.stow-n-tow.com 1-888-STOW-N-TOW or 810-359-4462 Stow-N-Tow Portable Storage Roll-off & Transport Trailer Specs 90 seconds for dropoff &amp ...

Looking for the weight of the boat, dry and/or wet weight. Would also like the weight of the dual axle trailer. Boat is 20' 6" long with a 4.3 litre engine, Alpha sterndrive.

i'll give it a try. trailer=1300#...sure about that one. boat w/o engine=2700#...pretty sure on that one. engine +drive=977#...pretty sure about that one. hope this helps. used to be a Fisher dealer. if it's critical, go to Trackerboats.com & contact the company.

2006-11-11 21:04:54 by lance_j@sbcglobal.net

Price: $39.99 $12.99

Built-In Molded Grill
Polypropylene Cone w/Cloth
5.25 Full Range Dual Cone Speakers

We have a custom built trailer, built 40 years ago. Due to the very special design of the trailer, a near exact replacement is needed.

DESCRIPTION: 2 inch wide, 4 Leaf, Flat end Slipper type, 29 1/2 inches from pivot center to end, 3/4 inch pivot ID, and the leaves are roughly 7/16 inch thick, or 400 thousandths as measured with micrometer. We do not know the load rating of this spring.

We do know the spring was salvaged from a very large mobile home's axle assembly.

Could you please help us find a source for replacements? The most important specifications are the width (2") and the pivot hole. (3/4") Possibly a different number of leaves could work also. Any and all suggestions will be appreciated very much.

Thank you for your help.

You should be able to find a "Spring" shop in your town. What they will need is either the spring itself, or all of the specs and weight capacity of the trailer, or all of the above. They will then custom make a new set of springs for you. It's best to replace both as a set rather than just replace a single spring.

Trying to find a new spring for a 40 year old trailer just isn't going to happen without any knowledge of where it came from or what it's off of.

2010-07-05 09:33:31 by Saturn 5

Price: $5.95 $5.95

I recently inherited a 1967 Marinette cabin cruiser, aluminum hulled, 26ft long. I have to haul it back to WA from AZ, and the trailer it's currently on is garbage. So I need a new one, but I have no idea how much this boat weighs or any of the technical specs. I have had no luck finding anything online. Does anyone know where I can find technical specifications, or approximately how much this boat would weigh?

take a look at the iboat link

http://www.iboats.com/Marinette_Boats/bp /20br1282

they don't show a 1967, 26' model, the listing starts in 68 with the following

1968 Fisherman
This inboard sportsfisherman is 28 feet long and weighs 5125 (pounds dry). This weight does not account for passengers, fuel, or gear. The beam of this craft is 126 inches.

1968 Express
This inboard cruiser has a aluminum hull, is 28 feet long and 126 inches wide at the widest point. The boat weighs approximately 4875 pounds with an empty fuel tank and without any gear or passengers.

The 1968, Sport Express is a 28 foot inboard boat. The weight of the boat is 4695 lbs

it appears that the 28' hull was the only size built by Marinette for the next several years, i feel confident that what you are getting is a 28' hull that will match one of the above descriptions.


hope this helps

2010-04-20 12:43:53 by Syllogistic Libertarian